Оборудование для автоматизации Системы умный дом
Базовый модуль релейного актуатора RMG 4 I KNX, 4-канальный, расширение до 12 каналов, съемный шинный контроллер, монтаж на DIN рейку, IP 20
Код товара: 47642
Артикул: TN:4930210
Базовый модуль релейного актуатора RMG 4 I KNX, 4-канальный, расширение до 12 каналов, съемный шинный контроллер, монтаж на DIN рейку, IP 20
Цену уточняйте
*Цены на сайте не являются офертой и носят ознакомительный характер, для уточнения актуальности цены вы можете связаться с оператором.
RMG 4 I KNX 4-х канальный базовый модуль релейного актуатора с измеряемым током каналов. Съемный шинный контроллер. N/O потенциальнонезависимые контакты.16А/ 250V cos=1, 16А/250V cos=0,6. Светодиодная индикация для каждого канала. Ручное переключение OFF-BUS-ON. Объкт обратной связи для каждого канала, центральные объекты. Режимы: Вкл/Выкл, цикличное вкл/выкл, ВКЛ/ВЫКЛ с задержкой, отключение с предупреждением. Логические функции: Disable (блокировка), АND (И), OR (ИЛИ), ENABLE (разрешить). Запись и вызов 8 сцен. Расширение до 12 каналов. Установка на ДИН-рейку. 10мА (с двумя модулями расширения)
4-way C load switching actuator MIX2
With current recognition
For higher lamp loads
Basic module MIX2
Can be upgraded to maximum of 12 channels
Up to two extension modules MIX or MIX2 can be connected to one basic module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of switching actuators is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)
Adjustable characteristics: e.g. switching, delayed switching, pulse function
Links, type of contact (NC contact/NO contact) and participation in central commands such as continuous On, continuous Off, central switching and save/call up scene
Switching functions: On/Off, pulse, On/Off delay, staircase light with warning
Logical links: e.g. lock, AND, release, OR
Operating voltage KNX Bus voltage, 10 mA
Operating voltage 110 – 240 V AC
Frequency 45 – 65 Hz
Stand-by consumption 1,3 W
Installation type DIN rail
Width 4 modules
Type of connection KNX bus terminal
Max. cable cross section Solid wire: 0.5 mm ( 0.8) to 4 mm | Stranded wire with end sleeve: 0.5 mm to 2.5 mm
Number of channels 4
Type of contact NO contact, 16 A, 10 A
Opening width < 3 mm
Resistive load 3680 W
Incandescent lamp load 2600 W
Fluorescent lamp load (conventional) parallel-corrected 19 x 58 W (7 µF), 28 x 36 W (4,5 µF), max. 1250 W (133 µF)
Fluorescent lamp load (conventional) not corrected 36 x 58 W, 54 x 36 W, max. 2600 VA
High-pressure metal vapour lamps 10 x 70 W (120 µF), 4 x 250 W (128 µF)
Fluorescent lamp load (electronic ballast) 30 x 36 W, 19 x 58 W, max. 1100 W
energy saving lamps 43 x 7 W, 29 x 11 W, 20 x 15 W, 15 x 20 W, 13 x 23 W
LED lamp < 2 W = 50 W or > 2 W < 8 W = 160 W
Voltage output 250 V AC
Frequency output 0 – 65 Hz
Switching output Potential-free
Switching of various phases Possible
Suitable for SELV Yes if all channels switch at SELV
Accuracy current measurement I > 1 A: ± 8 % of measured value; I < 1 A: ± 100 mA; lowest measurable value: 150 mA
Ambient temperature -5 °C … +45 °C
Type of protection IP 20
Protection class II according to EN 60 730-1
4-way C load switching actuator MIX2
With current recognition
For higher lamp loads
Basic module MIX2
Can be upgraded to maximum of 12 channels
Up to two extension modules MIX or MIX2 can be connected to one basic module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of switching actuators is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)
Adjustable characteristics: e.g. switching, delayed switching, pulse function
Links, type of contact (NC contact/NO contact) and participation in central commands such as continuous On, continuous Off, central switching and save/call up scene
Switching functions: On/Off, pulse, On/Off delay, staircase light with warning
Logical links: e.g. lock, AND, release, OR
Operating voltage KNX Bus voltage, 10 mA
Operating voltage 110 – 240 V AC
Frequency 45 – 65 Hz
Stand-by consumption 1,3 W
Installation type DIN rail
Width 4 modules
Type of connection KNX bus terminal
Max. cable cross section Solid wire: 0.5 mm ( 0.8) to 4 mm | Stranded wire with end sleeve: 0.5 mm to 2.5 mm
Number of channels 4
Type of contact NO contact, 16 A, 10 A
Opening width < 3 mm
Resistive load 3680 W
Incandescent lamp load 2600 W
Fluorescent lamp load (conventional) parallel-corrected 19 x 58 W (7 µF), 28 x 36 W (4,5 µF), max. 1250 W (133 µF)
Fluorescent lamp load (conventional) not corrected 36 x 58 W, 54 x 36 W, max. 2600 VA
High-pressure metal vapour lamps 10 x 70 W (120 µF), 4 x 250 W (128 µF)
Fluorescent lamp load (electronic ballast) 30 x 36 W, 19 x 58 W, max. 1100 W
energy saving lamps 43 x 7 W, 29 x 11 W, 20 x 15 W, 15 x 20 W, 13 x 23 W
LED lamp < 2 W = 50 W or > 2 W < 8 W = 160 W
Voltage output 250 V AC
Frequency output 0 – 65 Hz
Switching output Potential-free
Switching of various phases Possible
Suitable for SELV Yes if all channels switch at SELV
Accuracy current measurement I > 1 A: ± 8 % of measured value; I < 1 A: ± 100 mA; lowest measurable value: 150 mA
Ambient temperature -5 °C … +45 °C
Type of protection IP 20
Protection class II according to EN 60 730-1
Техническое описание
pdf, 325.2 Кбайт
